Site Logo E-PROJECTTOPICS

THE DESIGN AND CONSTRUCTION OF A DC TO AC POWER INVERTER INCORPORATED WITH AN AUTOMATIC SWITCH OVER BATTERY CHARGER


By


MEGWARA ALBERT U. EE/H2003/030



Presented To


Electrical/Electronic Engineering Department

πŸ“„ Pages: 32       🧠 Words: 3245       πŸ“š Chapters: 5 πŸ—‚οΈοΈ For: PROJECT

πŸ‘οΈβ€πŸ—¨οΈοΈοΈ Views: 239      

⬇️ Download (Complete Report) Now!

ABSTRACT
The system on this thesis is a DC Ò€" AC converter, which is an apparatus which is used for conversion of Direct Current to Alternating Current or signal.
In our country, this equipment is not all that in used not because it is not important but because people never give it a thought as per the construction and design.
It is meant, use with a 12v lead acid battery. If itÒ€s in a car for example a suitable output voltage of 230v AC is obtainable.
This output voltage of 230v AC can be used for powering small electrical appliances such as light, electric fans, radio, soldering iron etc.
However, it is worthwhile that AC operated with this appliance is nothing comparable to the AC generated by big generators. This is so because the voltage and power are less in terms of AC generation duration. This appliance is therefore suitable for short time replacement for the real AC generation especially in the remote areas and install where electrical appliances are sold and the need might arise for it to be tested and certified good. 

TABLE OF CONTENT
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
TABLE OF CONTENT

CHAPTER ONE
1.1 Introduction

CHAPTER TWO
INVERTER AND THEIR OPERATION 
2.1 Emitter
2.2 Base
2.3 Collector
2.4 Transistor Biasing
2.5 Important Biasing Rule
2.6 Transistor Currents
2.7 Summing Up
2.8 Transformer fundamentals

CHAPTER THREE
OPERATION AND DESIGN CONSIDERATIONS
3.0 Features of the Device
3.1 Dc supply unit
3.2 Inverter Unit
3.3 Step up Transformer Unit
3.4 Filter Unit
3.5 Triggering Unit
3.6 Battery Charging Unit
3.7 Switching Unit
3.8 Design
3.9 Inverter
3.10 Operation of the Device
3.11 General Circuit Diagram

CHAPTER FOUR
4.0 Construction
4.1 Packaging

CHAPTER FIVE
5.0 Conclusion 
5.1 Performance of the Designed
5.2 Power Inverter
5.3 Reference


πŸ“„ Pages: 32       🧠 Words: 3245       πŸ“š Chapters: 5 πŸ—‚οΈοΈ For: PROJECT

πŸ‘οΈβ€πŸ—¨οΈοΈοΈ Views: 239      

⬇️ Download (Complete Report) Now!

πŸ”— Related Topics

DESIGN AND CONSTRUCTION OF A METAL DETECTOR DESIGN AND CONSTRUCTION OF A SINGLE PHASE AUTOMATIC CHANGE OVER SWITCH WITH PHASE SELECTOR CONSTRUCTION OF AUTOMATIC CHANGE OVER SWITCH THE DESIGN AND IMPLEMENTATION OF AN ELECTRONIC SIGN PATTERN DISPLAY CONSTRUCTION OF 200W UNINTERRUPTIBLE POWER SUPPLY DESIGN AND CONSTRUCTION OF A 3 WAY INTER-COMMUNICATION SYSTEM THE DESIGN AND CONSTRUCTION OF 1000 KWA STABILIZER AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER AUTOMATIC PUMP CONTROL WITH WATER LEVEL MONITOR AND DIGITAL DISPLAY DESIGN AND CONSTRUCTION A SOLAR POWERED MOBILE PHONE CHARGER THE DESIGN AND CONSTRUCTION OF ELECTRIC ARC WELDING MACHINE DESIGN AND CONSTRUCTION OF A TWO LANE TRAFFIC LIGHT DESIGN AND IMPLEMENTATION OF MICROCONTROLLER BASED DTMF MULTIPLE DEVICES REMOTE CONTROL SYSTEM THE DESIGN AND CONSTRUCTION OF CAR CONTROLLER USING TELEMETRY SYSTEM DESIGN AND CONSTRUCTION OF 25AMPS SINGLE PHASE AUTOMATIC CHANGE OVER DESIGN AND CONSTRUCTION OF A 60 WATTS POWER AMPLIFIER DESIGN AND CONSTRUCTION OF AN AUTOMATIC VOLTAGE STABILIZER CONSTRUCTION OF 4600mAh POWER BANK THE DESIGN AND CONSTRUCTION OF AN ARC WELDING MACHINE DESIGN AND CONSTRUCTION OF VOLTAGE INVERTER SYSTEM WITH TRICKLE CHARGING SYSTEM

click on whatsapp